This pad is only considered chew proof when installed on one of our Chew Proof Armored™ frames. The "chew proof" part of it comes from the frame, which protects the edges and corners of the bed from your dog's teeth and gives your pup no place to latch on. The ballistic fabric of this pad will resist digging and scratching, but it can be chewed up if used outside of a frame.

This listing is for the replacement pad sling only, which will arrive folded in the box. No frame or rods are included. If you do not already have an armored frame to use with this pad, please purchase a full Chew Proof Armored™ bed instead.

The cover is made from 1200D ripstop ballistic polyester fabric, and the inner padding is 100% polyester fiberfill batting. The ripstop fabric has both a waterproof PU backing and a DWR coating to repel water.

Yes, our frames are standard sizes regardless of sling type, so you can use this replacement pad with any square-style frame (frames with squared-off corners). Since this replacement pad has its own padding, it can be used with both elevated and non-elevated frames.

Our ballistic material has a DWR treatment on top and a waterproof PU backing applied to the inner surface. These additions will help keep water from soaking into the bed, but seams can be a point of entry for fluid. For that reason, our beds are considered water-resistant, not 100% waterproof. Clean up spills as quickly as possible to reduce the chance of leakage into the bed padding.

Please note that water-resistance refers to regular water, as in moisture from weather, sprinklers, or water bowl spills. Bodily fluids like urine and vomit are more caustic and can seep past the DWR treatment and PU backing if not wiped up quickly. Frequent exposure to urine or vomit can damage these protective coatings, making the bed more vulnerable to fluids in the future.

Simply wipe the pad down with a damp cloth or scrub away any stubborn spots with soap and warm water. For a more thorough cleaning, you can remove it from the frame (not included) and machine wash it in cold water on a delicate cycle and then machine dry low heat until fully dry.

Yes, this pad must be used with one of our Chew Proof Armored™ frames. It is not chew proof on its own, and in fact it has delicate sleeves along the edges that are intended to be covered by a frame. If used outside the frame, these spots will be left exposed and can be easily damaged by even a less destructive dog. Pads used without frames are not covered under warranty.

If you do not already own a Chew Proof Armored™ frame, please purchase a full bed here instead.

We do not sell the frames or rods separately, so if you do not have one already please make sure to purchase a full Chew Proof Armored™ bed instead. You can find them here.

For best results, measure the dimensions of your current frame (from the outside edges of the corners). The dimensions listed for our pads refer to the frame dimensions rather than the actual fabric size, so you'll want to click the option that matches up with your frame's dimensions. Do not base it off the sleeping area dimensions of the pad itself.

You can also check the size listed on the care tag on the underside of the pad (if it has not been removed), or you can review your order history by accessing your account on our site.

To swap out your old pad with a new one, please follow these steps:

1. Use a 4.5 mm allen/hex key to open all four corners of your bed's frame
2. Remove the corners and slide the frame pieces off the center fabric
3. Slide the rods out from the sleeves of the fabric. Do not discard rods. You will need these to put the bed back together, and we do not sell or carry extras
4. Insert the rods into the sleeves on the new center fabric
5. Slide the frame pieces over the sleeves
6. Attach the four corners one at a time. For best results, install in a crisscross pattern (i.e. upper right corner first, then lower left, then upper left, then lower right) and tighten the screw by hand only. This will give you extra wiggle room when it comes time to put the last corner on, which can be challenging
7. Once all four corners are in place and hand-tightened, go back with the allen/hex key and fully tighten all four screws
8. If you have an elevated bed, you can insert the legs back into the corners and twist until tight. The bed is now ready for use!